Initial commit

notes/assembly_notes.txt

@@ -0,0 +1,11 @@
+ASSEMBLY NOTES (UNLESS OTHERWISE SPECIFIED)
+
+1)	DO NOT POPULATE COMPONENTS ARE MARKED WITH A RED CROSS
+
+2)	DO NOT POPULATE COMPONENTS ARE NOT PRESENT IN THE BOM
+
+3)	IF CONFLICTING INFORMATION IS FOUND BETWEEN THE ASSEMBLY
+	FILE AND BOM, BOM SHOULD BE USED AS THE MAIN SOURCE.
+
+4)	DOT IDENTIFIES PIN #1 LOCATION AND DEVICE ORIENTATION
+	WHEN VIEWED FROM THE TOP.

notes/fabrication_notes.txt

@@ -0,0 +1,62 @@
+FABRICATION NOTES (UNLESS OTHERWISE SPECIFIED)
+
+1)	FABRICATE PER IPC-6012A CLASS 2.
+
+2)	OUTLINE DEFINED IN SEPARATE GERBER FILE WITH
+	"Edge_Cuts.GBR" SUFFIX.
+
+3)	SEE SEPARATE DRILL FILES WITH ".DRL" SUFFIX 
+	FOR HOLE LOCATIONS.
+
+	SELECTED HOLE LOCATIONS SHOWN ON THIS DRAWING 
+	FOR REFERENCE ONLY.
+
+4)	SURFACE FINISH: ${pcb_finish_cap}
+
+5)	SOLDERMASK ON BOTH SIDES OF THE BOARD SHALL 
+	BE LPI, COLOR ${solder_mask_color_text_cap}.
+
+6)	SILK SCREEN LEGEND TO BE APPLIED PER LAYER 
+	STACKUP USING ${silk_screen_color_text_cap} NON-CONDUCTIVE EPOXY INK.
+
+7)	ALL VIAS ARE TENTED ON BOTH SIDES UNLESS 
+	SOLDERMASK OPENED IN GERBER.
+
+8)	RESERVED
+
+9)	PCB MATERIAL REQUIREMENTS:
+
+	A.	FLAMMABILITY RATING MUST MEET OR EXCEED 
+		UL94V-0 REQUIREMENTS.
+	B.	Tg 135 C OR EQUIVALENT.
+
+10)	DESIGN GEOMETRY MINIMUM FEATURE SIZES:
+
+	BOARD SIZE				${bb_w_mm} × ${bb_h_mm} mm
+	BOARD THICKNESS		${thickness_mm} mm
+	TRACE WIDTH			${track_mm} mm
+	TRACE TO TRACE		${clearance_mm} mm
+	MIN. HOLE (PTH)			${drill_pth_real_mm} mm
+	MIN. HOLE (NPTH)		${drill_npth_real_mm} mm
+	ANNULAR RING			${oar_mm} mm
+	COPPER TO HOLE		${c2h_mm} mm
+	COPPER TO EDGE		${c2e_mm} mm
+	HOLE TO HOLE			${h2h_mm} mm
+
+11)	ALL DIMENSIONS ARE IN MILLIMETERS UNLESS OTHERWISE
+	SPECIFIED.
+
+12)	FOR REFERENCE ONLY THE STACKUP CORRESPONDS TO JLCPCB
+	STACKUP JLC04161H-7628.
+#?stackup and impedance_controlled
+
+#?stackup and impedance_controlled
+13)	REFER TO IMPEDANCE TABLE FOR IMPEDANCE CONTROL REQUIREMENTS.
+#?stackup and impedance_controlled
+	THE SUPPLIED ARTWORK MAY OR MAY NOT CONTAIN THE SPECIFIED
+#?stackup and impedance_controlled
+	TRACE GEOMETRIES ON EVERY LAYERS SPECIFIED.
+#?stackup and impedance_controlled
+
+#?stackup and impedance_controlled
+14)	CONFIRM SPACE WIDTHS AND SPACINGS.

notes/impedance_table.txt

@@ -0,0 +1,4 @@
+Layer,	Ref1,	Ref2,	Type,	Impedance [ohms],	Width [mil],	Space [mil],	Tolerance
+L1,		AIR,	L2,		SE,		50,					13.75,			-----,			10%
+L1,		AIR,	L2,		DIFF,	90,					11.26,			8.00,			10%
+L1,		AIR,	L2,		DIFF,	100,				8.68,			8.00,			10%

notes/schematic_notes.txt

@@ -0,0 +1 @@
+Unless otherwise specified, components Values are in ohms, µF, and µH.